BBC BASIC Programmers' Reference

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
=====Minimizing sound clicks=====

//by Richard Russell, January 2010//\\ \\  When generating music using the [[http://www.bbcbasic.co.uk/bbcwin/manual/bbcwin7.html#sound|SOUND]] statement, **clicks** may sometimes be audible at the start and/or end of notes. These clicks are likely to be more noticeable when listening in high-quality, such as on headphones or when feeding the PC's sound output to a hi-fi system.

There are four main causes of such clicks; these are listed below along with methods for minimizing the effect.
 
===== Using SOUND OFF =====

Never use SOUND OFF to terminate a playing note; this shuts down the entire BB4W sound system and is likely to result in a large output transient. To terminate a note before its duration has been completed (or when the duration has been set to 'infinite') use the **flush** bit.

Instead of:

<code bb4w> 
        SOUND OFF
</code>

Use:

<code bb4w>
        SOUND &10, 0, 0, 0
        SOUND &11, 0, 0, 0
        SOUND &12, 0, 0, 0
        SOUND &13, 0, 0, 0
</code>

===== Sudden amplitude changes =====

If you are using the 'constant amplitude' form of the SOUND statement (where the second parameter is negative) then, when you need to change the amplitude, do so gradually.

Instead of doing this:

<code bb4w>
        SOUND 1,-15,148,20
        SOUND 1,-10,148,20
</code>

Do this:

<code bb4w>
        SOUND 1,-15,148,18
        SOUND 1,-14,148,1
        SOUND 1,-13,148,1
        SOUND 1,-12,148,1
        SOUND 1,-11,148,1
        SOUND 1,-10,148,18
</code>
   
Or consider using envelopes to achieve a similar effect:

<code bb4w>
        ENVELOPE 1,1,0,0,0,0,0,0,20,0,0,-20,120,0
        ENVELOPE 2,1,0,0,0,0,0,0,-20,0,0,-20,80,0
        SOUND 1,1,148,20
        SOUND 1,2,148,20
</code>

===== Excessive attack or release rates =====

If you are using an amplitude envelope (where the second parameter of the SOUND statement is positive) don't make the attack and release rates too great.

For example, instead of using:

<code bb4w>
        ENVELOPE 1,1,0,0,0,0,0,0,127,0,0,-127,126,0
</code>

Use:

<code bb4w> 
        ENVELOPE 1,1,0,0,0,0,0,0,20,0,0,-20,126,0
</code>
(where the attack and release rates have been reduced from 127 to 20).

===== Rests (silent notes) =====

If you need a period of silence on a particular channel (a **rest**) use one or other of the following techniques, depending on whether you are using a constant amplitude or an envelope:

==== Constant amplitude ====

Set the //pitch// to zero, **not** the //amplitude//.\\ \\  Instead of:

<code bb4w>
        SOUND 1,-15,148,10
        SOUND 1,0,148,10 : REM rest
        SOUND 1,-15,100,10
</code>

Use:

<code bb4w>
        SOUND 1,-15,148,10
        SOUND 1,-15,0,10 : REM rest
        SOUND 1,-15,100,10
</code>

==== Amplitude envelope ====

Use the **hold** bit to allow the sound to decay rather than stop suddenly:\\ \\  Instead of:

<code bb4w>
        ENVELOPE 1,1,0,0,0,0,0,0,20,0,0,-20,126,0
        SOUND 1,1,148,10
        SOUND 1,1,0,10 : REM rest
        SOUND 1,1,100,10
</code>

Use:

<code bb4w>
        ENVELOPE 1,1,0,0,0,0,0,0,20,0,0,-20,126,0
        SOUND 1,1,148,10
        SOUND &1001,1,0,10 : REM rest
        SOUND 1,1,100,10
</code>